APS Spring 2012 : Page 108J/80 J/80 Main Halyard J/80 Standing Rigging (Before ordering, go to apsltd.com/HowtoMeasureStandingRigging.) J80800 Upper Shroud 7/32” Open Turnbuckle to T-Ball (one) J80801 Upper Shroud 7/32” Ronstan Calibrated to T-Ball (one) J80810 Intermediate Shroud 5/32” Open Turnbuckle to T-Ball (one) J80811 Intermediate Shroud 5/32” Ronstan Calibrated to T-Ball (one) J80820 Lower Shroud 3/16” Open Turnbuckle to T-Ball (one) J80821 Lower Shroud 3/16” Ronstan Calibrated to T-Ball (one) RF157305 Sealoc Handle Kit (one) J80830 Upper Backstay, 5/32” Wire with Fork/Marine Eye (one) J80840 Backstay Leg 1/8” Fork/Open Turnbuckle with Block (one) JH38210 Diamond Plate -Backstay $215.29 $249.67 $127.90 $159.31 $140.65 $179.32 $54.78 $93.29 $98.37 $4.50 Our J/80 main halyard is constructed of 5/16” diameter line -choose from Yale Crystalyne, New England V100 or New England VPC. Crystalyne and V100 are both 100% Vectran cored double-braid lines with hard-wearing polyester covers. Vectran is a workhorse fiber, operating at high percentages of its breaking strength with no creep or stretch -it’s also lightweight and non-water absorbing. VPC is a blended core, double-braid with Vectran carrying the load and polypropylene providing lightweight bulk. This line also has a hard wearing polyester cover; a more economical solution for club racers who don’t need top level performance from a halyard. We splice a Wichard screw pin halyard shackle on the working end and a reeving eye on the other for easy installation. J80100 5/16” Crystalyne with Shackle $176.60 J80101 5/16” V100 with Shackle $200.60 J80102 5/16” VPC with Shackle $139.85 J/80 Jib Halyard Our J/80 jib halyard is constructed of 5/16” diameter line -choose from Yale Crystalyne, New England V100 or New England VPC. Crystalyne and V100 are both 100% Vectran cored double-braid lines with hard-wearing polyester covers. Vectran is a workhorse fiber, operating at high percentages of its breaking strength with no creep or stretch -it’s also lightweight and non-water absorbing. VPC is a blended core, double-braid with Vectran carrying the load and polypropylene providing lightweight bulk. This line also has a hard wearing polyester cover; a more economical solution for club racers who don’t need top level performance from a halyard. We splice an eye at the working end to attach to the shackle on the upper furling swivel and a reeving eye on the other for easy installation. J80120 5/16” Crystalyne with Eye $135.94 J80121 5/16” V-100 with Eye $157.06 J80122 5/16” VPC with Eye $103.60 Sparcraft J/80 parts... Karl’s Boat Shop Tiller An extremely stiff, split tiller keeps excess weight to a mininum leaving you with a lighter, more sensitive feeling helm. 11” rise to clear your knees and provide better leverage angle while driving. 60-7/8” long. Butt dimensions: 2-1/8” x 1-11/16”. 3.5 pounds. KBJ80T $439.00 J/80 Spinnaker Halyard J/80 Replacement Tiller Laminated tillers of alternating strips of 1/4” mahogany and ash, finished with four coats of varnish. Length is 61-1/2”. The butt is 1-3/4” wide by 2-1/4” high. The rise is 11-1/2”. HM1264F $122.66 Lifting Straps Great for hoisting/launching the J/80. Constructed of a durable, two-ply material with the strap’s load rating sewn near one of the loops for safety. Both ends are covered with a chafe-resistant material to increase the durability of the loop at the connection point. The wide shackle fits under the lifting bar on the keel. SECEE2102X5 SECM702 Lifting strap, 2” diameter x 5’ Lifting shackle, 2” inside width $35.80 $75.00 All our J/80 spinnaker halyards meet the 6mm diameter class minimum. We recommend our 5/16” stripped to 1/4” MaxiBraid Plus or EnduraBraid halyards for the best holding power. They leave only the Dyneema core (non-water absorbing) up the mast when hoisted and a larger diameter tail that is easy to grip, both in your hands and at the cleats. A Ronstan RF6110 snap shackle is 12-strand spliced to the working end with a stopper ball. The bitter end has a reeving eye for easy installation. We also offer 1/4” non-stripped halyards as well, just ask. All our spinnaker halyards are available in just the right lengths for either your Hall or Sparcraft mast. J80150 5/16” MaxiBraid Plus, Stripped -Hall $211.76 J80151 5/16” Endura Braid, Stripped -Hall $274.08 J80210 5/16” MaxiBraid Plus, Stripped -Sparcraft $221.47 J80211 5/16” Endura Braid ,Stripped -Sparcraft $289.11 J/80 Mainsheet APS Spinnaker Launching Bag Mesh design. Nice and deep so you can stuff the spinnaker down, and it won’t blow back out. Slight taper at the bottom. Measures approximately 25” fore and aft, 25” side to side and has an 30” depth. Battens on all four sides of the opening. Large race instructions pouch/window with Dacron backing to keep a wet spinnaker from getting papers wet. Slots inside the pocket for pencils. Two side mesh pockets with Velcro flaps securely keeps your VHF safe and within reach. APSC500 $129.95 Our J/80 mainsheets assume you use a 2’ pennant between the boom bail and top mainsheet block. This reduces your mainsheet length by about 8’ and makes for less sheet to pull in when rounding the leeward mark. We offer single braidsmainsheets in Swiftcord, Ph.D. and Racing Sheet. MLX has a more traditional feel with less water absorption than an all polyester line. Newswift is our lowest stretch mainsheet with a double braid construction and a firm hand. We eye splice the end that attaches to the becket on the fiddle and whip the bitter end. We offer a 3/16” Dyneema pennant with an eye splice on each end --just luggage tag it to your boom and attach to the shackle on your mainsheet block. J80311 3/8” Swiftcord $123.01 J80313 3/8” MLX $142.90 J80314 3/8” Newswift $167.28 J80315 3/8” Racing Sheet $143.15 J80316 3/8” Ph.D. $129.90 J80320 Mainsheet Block Pennant 3/16” Amsteel Blue $30.12 More J/80 spinnaker sheet options... and a Greatly expanded selection of J/80 products J/80 Upgraded Rudder Fittings These robust fittings replace the failure prone ones found on the stock US J/80’s. Heavy gauge stainless steel gives you peace of mind. JBS001 Transom Gudgeons -Pair $133.00 JBS002 Long Pin $45.00 JBS003 Tiller Straps -Pair $113.00 JBS004 Rudder Gudgeons -Pair $333.00 J/80 Tack Line Clutch Upgrade Spinnaker tack lines can become so highly loaded that releasing them at a critical moment can be difficult. Replace your cam cleat on the starboard cabin side with an easy to operate Spinlock XAS clutch. When its time to “blow” the tack line, just pull the lever and it’s done immediately. Spinlock’s side mount kit makes mounting a breeze. XAS clutch with side mount conversion shown. SPXAS04081 XAS Clutch $74.05 SPXASSMNT XAS Side Mount Conversion $44.47 J/80 “Y” Configuration Spinnaker Sheet Our J/80 bridle “Y” spinnaker sheet is constructed of 5/16” diameter line using either Yale Maxibraid Plus or New England Endura Braid. Each sheet has the cover stripped back about 1/3 of the total sheet length and the stripped ends are spliced together leaving a single 3’ end to tie to the clew. The advantage of the “Y” is less snagging on the forestay when the sheets are running during a jibe and the 3’ tail allows for easy assembly/rigging. J80305 5/16” Maxibraid Plus $276.64 J80306 5/16” Endura Braid $385.32 108 Find More Info and Shop 24/7 at www.APSltd.com J/80Publication List Using a screen reader? Click Here |
